Hikaru V60 Smart Brewer in test: temperature top, water distribution flop
The Hikaru V60 from Hiroia delivers the most precise temperature consistency we've ever measured in a filter coffee machine. Despite this, we don't recommend it because of conceptual weaknesses in water distribution and a price of 700 to 800 CHF that bears no relation to performance.
Why we did this test
We systematically test filter coffee machines. The Hikaru is the most expensive consumer machine in this series. Our test protocol includes temperature measurement, brew profile analysis, and sensory evaluation. We worked with both the included Hario V60 and alternative brewers.
Technical specifications
The Hikaru operates with a boiler system (700 ml, 830 W) and offers an adjustable temperature range of 80 to 96 degrees Celsius. The flow rate can be adjusted in 10 steps from 1 to 10 ml per second. There are 9 presets, divided into three sizes (S/M/L) and three roast levels (Light/Medium/Dark Roast). Control is via an app (iOS 13+, Android 10+) or three buttons on the device. The shower head has 5 holes on a diameter of approximately 2.5 cm, which corresponds to a 1-euro coin. The warm-up time is approximately 4 minutes at cold start.

Temperature measurement: best value
We measured three brews at different temperature levels. Profile 2 at 92 degrees, Profile 3 at 85 degrees, and Profile 4 at 96 degrees. The machine maintains the set temperature throughout the entire brew with a maximum deviation of 1 degree. That is extraordinary. For comparison: even high-quality consumer machines show 3 to 5 degree temperature fluctuations.
The three temperature curves run almost horizontally. At 85 degrees, the machine stays between 84.1 and 85.5 degrees. At 96 degrees between 95.2 and 96.0 degrees. At 92 degrees between 91.4 and 93.1 degrees.
The technical explanation: The boiler is completely heated before brewing. There is no flow-through heater effect that would reach its performance limit at higher flow rates. This results in constant temperature.
Water distribution: the core problem
The shower head has five holes on a diameter of approximately 2.5 cm. The water hits the coffee bed centrally. With a conical filter like the Hario V60, this means: the center is strongly swirled, the edge is less affected by the swirling, leading to under-extraction.
We brewed 18 g of coffee with profile S (290 ml, 5 pulses). The water barely reaches the outer coffee particles. They get wet, but are not swirled. The extraction is uneven. You can taste it: the coffee has little body, with a slightly dry, dull note in the finish.
With manual pour-overs, we control water distribution through movement of the kettle or through spiral pouring patterns. The Hikaru shower head is fixed. It can't compensate for this.

Attempted solution: Orea and Mellow Dripper
We repeated the brew with an Orea flat-bed filter. We also placed a Melodrip between the machine and filter. The Melodrip has its own shower head that redistributes the water and reduces impact speed.
Our recipe: 16 g coffee, 250 ml water, 5 pulses of 50 ml each, 93 degrees (Light Roast).
The result: The coffee, a Rwandan natural called Shyira, is juicy, balanced, has body. The dryness is gone. The extraction is significantly more even.
The setup works, but it requires two additional components (Orea, Melodrip) that are not included and whose existence most buyers won't know about. An 800-euro machine should brew good coffee without such workarounds.
Our video on the Orea dripper.
App and operation
The app, called Hikaru Brew, is functional. We can freely set flow rate (1 to 10 ml/s), temperature (80 to 96 degrees), pulse sequences, and pause times. There's a recipe library with proven profiles from professionals. QR code sharing works. The Bluetooth 5.2 connection is stable.
Our criticism: The preset profiles (S/M/L) cannot be edited directly. We have to copy them into our own profiles. That's cumbersome. The app announces an update that will add this feature; it wasn't available at the time of testing.
The machine has no rinse function. We can't pre-rinse the paper without creating a separate profile for it. That's a detail, but it shows: the software isn't fully thought through.
Operation without the app: Three buttons (S/M/L) on the device. That's enough for everyday use. We only need the app for custom recipes.
Boiler versus flow-through heater: Why boiler makes sense here
We wondered why Hiroia installed a boiler. The 4-minute warm-up time is longer than with a flow-through heater, for example with the Melitta Epos at about 1.5 minutes.
The physical limits: A flow-through heater can't maintain the target temperature at high flow rates (for example, 10 ml/s). We've measured this in other tests: at 6 to 7 ml/s, the temperature drops 3 to 5 degrees. The Hikaru brews at up to 10 ml/s, which only works with a boiler or a flow-through heater with high energy input.
The trade-off: We accept the 4-minute warm-up time if the machine delivers. With the Hikaru, it does, but only in a very specific setup, see Orea solution.
Comparison: Sage Smart Brewer, Melitta Epos
Both cost about a quarter, so 200 to 250 CHF. Both have similar material construction, a plastic-metal mix. The Melitta Epos has a larger shower with a better distribution pattern. The Sage has a shower head with a radial design. Both brew better coffee than the Hikaru in standard setup without workarounds.
Temperature consistency: The Epos fluctuates by 2 to 3 degrees, the Sage by 3 to 4 degrees. That's worse than the Hikaru, but in practice less relevant if the water distribution is correct. Even extraction at 91 degrees is better than uneven extraction at exactly 93 degrees.
Price justification: The Hikaru costs four times as much. For this we get: more precise temperature, more setting options, LED light show during brewing. That doesn't justify the price premium.
Who should buy this machine?
The target audience according to the manufacturer: coffee professionals and enthusiasts who want reproducible brews.
The real target audience from our perspective: people who first already own an Orea or similar flat-bed filter, second are willing to experiment with Melodrip or similar adapters, third prioritize temperature consistency above all else, and fourth have 800 CHF to spare and don't want to take the path of least resistance.
Not suitable for: anyone who expects a plug-and-play solution.
Design and construction
The machine looks like it was built for Instagram. Fluted surface, LED ring, round shapes. In practice, the LED blinking after 20 minutes is annoying. It can't be turned off, only the signal tone.
Construction: solid. Plastic (Tritan, BPA-free), stainless steel shower head, glass carafe. Nothing rattles, nothing feels fragile. But nothing justifies 800 CHF.
Conclusion
The Hikaru V60 is a technical demonstration unit for temperature consistency. Anyone who needs temperature curves for research purposes will find the best tool on the consumer market here. Anyone who just wants to drink good coffee should go with the Melitta Epos, save 600 CHF, and enjoy better cups.
Our advice: If Hiroia builds a version with an optimized shower head, larger diameter, more holes, possibly rotating, we're happy to test again. Until then: skip it.
















