Brew time, extraction time, pull time — three words for the same principle. And yet there's confusion about when you should actually start counting. At the button press? At the first drop? We'll clarify that. (Are you looking for a complete guide to espresso preparation? You'll find it in our espresso preparation guide.)
Brew time is contact time
Whether you call it brew time, extraction time, or pull time: it always means the contact time between water and coffee. Nothing more, nothing less.
Extraction begins the moment hot water hits your coffee puck. Not when the first drop falls into the cup. And it ends when the pump stops working and no more water is forced through the coffee.
That sounds simple, but in practice it regularly leads to misunderstandings. Because between the moment you start the pull and the moment water actually reaches the coffee, one to four seconds can pass depending on the machine.
When should you start counting?
The short answer: When your machine dispenses water.
With most machines, this happens almost immediately when you press the button or pull the lever. Then the button press is your start signal. With some machines there's a small delay of one or two seconds — you can test this easily by running it once without the portafilter and seeing when the water comes. You simply subtract this latency.
Why not count from the first drop? Because between water contact and the first drop in the cup, several seconds of extraction already take place. The water must first permeate the entire coffee puck before anything arrives at the bottom. If you only start counting from the first drop, you're missing several seconds of contact time — and your recipe is no longer accurate.
And it's precisely those first seconds of contact between water and coffee that significantly determine the entire extraction time. This is where you can already see whether the grind size was chosen correctly or not.

What scales with drop detection can do (and what they can't)
Some scales automatically start the timer as soon as the first drop hits the scale. As a time measurement for brew time, that's not useful because it doesn't reflect the beginning of extraction.
Still, the function isn't worthless. It can tell you something about your coffee: If the first drop arrives after three seconds, you're probably grinding too coarse. If nothing comes for ten seconds, the grind size is probably too fine — or your puck has a problem. As a diagnostic tool, drop detection is useful. As a stopwatch for brew time, it's not.
We've included our favorite scales in our shop. There's something in every price range.
Vibratory pump vs. rotary pump: The difference that changes your recipes
This is where it becomes practically relevant, because your pump determines how you need to interpret recipes.
A rotary pump builds pressure almost instantly. Within seconds, full brew pressure is on the coffee. The brew chamber fills, water hits the puck, and you're off. With a rotary pump, button press and extraction start are practically the same.
A vibratory pump works differently. It takes significantly longer to build pressure — the flow starts slowly and increases over several seconds. This means: Contact time is running, but the first phase is far from as intense as with a rotary pump. The coffee is essentially automatically gently pre-wetted before full pressure arrives.
This has consequences for your recipes.

The +3-second rule
Most recipes you get from roasteries — "18 g in, 36 g out, 25 seconds" — are made with rotary pumps. That's because many roasteries use professional commercial machines, and those almost always have rotary pumps.
If you have a vibratory pump at home (and that applies to the vast majority of home machines), you'll need about three seconds more for such recipes. So: 25 seconds recipe time → around 28 seconds on your machine. This isn't an exact law, but a good benchmark to get you in the right ballpark.
At Kaffeemacher, we typically provide our recipes for both vibratory and rotary pumps and mark them accordingly. If you're unsure about a roastery, ask which machine the recipe was created with. That gives you a better reference point than any rule of thumb.
Extraction time for single and double espresso
A question that comes up often: Does a double espresso need to run longer than a single?
Not necessarily. If you use double the amount of coffee in a larger basket for a double espresso and run double the amount of water through it, the contact time often remains similar. The resistance of the coffee puck and the flow rate scale with it. What changes is the brew ratio — and that should remain constant. A 1:2 ratio (18 g coffee → 36 g espresso) applies to the double just as a 1:2 ratio (9 g → 18 g) applies to the single. Though single espressos always have their own unique dynamics. Little coffee powder doesn't build resistance as evenly as the coffee powder in a double espresso. A reason why we tend to recommend making double extractions instead.
Extraction time is your control tool: If the time doesn't match at the same brew ratio, the grind size is probably wrong.
Brew time as guidance, not as law
25 seconds is not a magic number. We provide recipes as time windows, not as second-precise specifications. The reason: Each machine behaves slightly differently, each coffee reacts slightly differently, and two seconds more or less make little difference in taste with a well-dialed recipe.
Use brew time as a reference value. If you land at 22 seconds with 18 g coffee and 36 g espresso, you're probably grinding a bit too coarse. At 35 seconds, too fine. But whether 26 or 28 seconds — try it and decide by taste.
In the end, what matters is what's in the cup. Brew time helps you get there. But it doesn't replace your taste buds.
Want to know how pre-brewing and pre-infusion affect extraction time? We explain that in the article pre-brewing with espresso: What does it really do? — including the question of why 3 seconds of pre-infusion is almost always too little.
This article is also available as a video on our YouTube channel.

















